Ht-instruments FULLTEST3 Bedienungsanleitung Seite 14
- Seite / 92
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
FULLTEST 3
EN - 13
5. MEASUREMENTS
5.1. CONTINUITY - TWO WIRE METHOD (RPE-2WIRE)
Complying with EN 60204-1, continuity of protective bonding circuit between PE terminal and
relevant points of the protective conductor system must be checked by injecting a measurement
current of 0.2 A up to 10 A approx.
5.1.1. RPE-2WIRE DISPLAY EXPLANATION
Adjustable/selectable parameters:
Im NOM - nominal measurement current 200 mA or 25 A AC
LIMIT (meas. current 200 mA) - continuity limit value 0.01 19.99, 20.0 200.0
LIMIT (meas. current 25 A) - continuity limit mode STANDARD, 60204 SET Z or 60204 SET L
LIMIT (test current 25 A, STANDARD mode) -
continuity limit value 0.01 20.00
MODE - measurement mode MANUAL or TIMER
CAL (meas. current 200 mA) - calibration of test leads 0.00 5.00
CAL (meas. current 25 A) - calibration of test leads 0.000 1.999, 2.00 5.00
TIMER - measurement time 00:01 60:00 (1 s 60 min), resolution 1 s
LENGTH - wire length 0.1 999.9 m, resolution 0.1 m
SECTION - wire section 1, 1.5, 2.5, 4, 6, 10, 16, 25, 35, 50 or 70 mm
2
MATERIAL - wire material Cu (Cupper) or Al (Aluminium)
ZLINE - input line impedance 0.001 2.000 , resolution 0.001
PROTECTION - over-current protection device MCB B, MCB C, MCB D, MCB K, FUSE gG or
FUSE aM
In - nominal current of protection device Depends on selected protection device, see the
chapter 5.1.3. LIMIT VALUE ADJUSTMENT
Figure 5: Display with RPE-2WIRE test result
1 ..... Selected function.
2 ..... Progress bar, it follows measurement time during the measurement (in TIMER mode only).
3 ..... Sub-result - measurement current Im that was flowing through UUT during the measurement.
4 ..... Measurement screen touch-screen key.
5 ..... Im NOM touch-screen key to select nominal test current (200 mA or 25 A). Currently selected value
is displayed on the bottom of the key.
- FULLTEST 1
- FULLTEST 3 2
- Table of contents: 2
- 2. GENERAL DESCRIPTION 7
- 3. PREPARATION FOR USE 10
- 4. OPERATING INSTRUCTIONS 11
- PE-2WIRE function 13
- 5. MEASUREMENTS 14
- Short unisolated wire 15
- Red test leads 2,5 mm 15
- PE-2WIRE MEASUREMENT 17
- NOM (5) 17
- PE-4WIRE DISPLAY EXPLANATION 19
- PE-4WIRE test result 19
- PE-4WIRE MEASUREMENT 21
- PE 0 20 21
- ISO DISPLAY EXPLANATION 23
- ISO test result 23
- ISO MEASUREMENT 24
- APP or IREAL 27
- APP 0 200 mA 28
- REAL 0 200 mA 28
- TES NOM 28
- 29
- L/N and UL/PE will start to 33
- IN/2 IN 2IN (4) 5IN 33
- SC LIM, which is the bases 35
- SC MIN must 36
- L/N or LOOPL/PE measurement 38
- L/N measurement 38
- L/L measurement 38
- L/PE will start to be 42
- IN and actual trigger 47
- RES PLUG measurement 47
- IN within required range 47
- APP 0 5.06 kVA 50
- L/N 195 253 V 50
- L 0 20 A 50
- PE 0.25 mA 10 A 50
- L1/2 360 460 V 53
- L2/3 360 460 V 53
- L3/1 360 460 V 53
- CLAMP DISPLAY EXPLANATION 54
- CLAMP test result 54
- CLAMP measurement 55
- LEAK measurement, CLAMP mode 58
- L/N 195 253 V 59
- PE CURRENT OVERRANGE! 60
- L CURRENT OVERRANGE! 60
- MEMORY LANGUAGE SETUP 61
- OPERATOR TESTER INFO 61
- USBCLEARMEM INFO 61
- LAST RESULT 62
- LANGUAGE 63
- TESTER INFO 63
- DATE/TIME NOMINAL VOL 64
- LEVEL NAMES 64
- SAFET INPUT RESETCONTACT VOL 64
- 50 V25 V 65
- CONTACT VOL 65
- EN - 65 66
- EN - 66 67
- EN - 67 68
- EN - 68 69
- 230 V 240 V 70
- NOMINAL VOL 70
- DISABLED ENABLED 70
- SAFETY INPUT 70
- 7. MEMORY FEATURES 72
- 8. MEMORIZING EXAMPLE 73
- 9. RECALL RESULTS 75
- EN - 75 76
- 13. MAINTENANCE 77
- A or RCD function 78
- PE measurement 79
- PE-4WIRE, 25A) 80
- PE-2WIRE, 0.2A)) 80
- N CAT III 300 V 82
- L/PE): 450 k 85
- C at IN: 85
- TRIG): 0 460 VAC 86
- RES): 100 M 86
- TRIG): 450 k 86
- APP and PACT CAT II 300 V 87
- PE (POWER) 87
- L1/2, UL2/3, UL3/1 88
- CLAMP) 88
- 15. SERVICE 91
Verwandte Produkte und Handbücher für Werkzeug Ht-instruments FULLTEST3
(4 Seiten)
Werkzeug Ht-instruments GEO416 Bedienungsanleitung
(116 Seiten)
(116 Seiten)
Werkzeug Ht-instruments HT21 Bedienungsanleitung
(17 Seiten)
(17 Seiten)
Werkzeug Ht-instruments HT32 Bedienungsanleitung
(23 Seiten)
(23 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern